I have been playing with a new Triquint ULNA device (TQP3M9036). It
Shows a lot of promise. It is like a MAR or MSA device in that it is
50ohm in and out. and has a claimed NF about .4db nf ( their numbers).
I have built several pramps to test them and have gotten even better
than they claim and they cover 50-1296 with ease and NF is .4ish or
below. The S11 and S22 are both great and the OIP3 is +35db also
...very nice device. It has great promise as a good terrestrial LNA.
Preamps are foolproof to build and would cost under $50 if all the best
quality parts are used.
Just for information only ...
Pete WA2ODO
--
++++++CONFIDENTIALITY NOTICE++++++
The information in this email may be confidential and/or privileged. This email is intended to be reviewed by only the individual or organization named above. If you are not the intended recipient or an authorized representative of the intended recipient, you are hereby notified that any review, dissemination or copying of this email and its attachments, if any, or the information contained herein is prohibited. If you have received this email in error, please immediately notify the sender by return email and delete this email from your system.
Hi all,
I’m ready on 6cm with the same dish I’m using on 3cm.
Despite the strong local 5 GHz WiFi noise, had a nice 579/569 first QSO with this setup today with HB9Q, thank you Dan !
Setup is a 3.7m dish and 60W at CP feeder.
I can be QRV on 6cm or 3cm most of the days, skeds and tests are very welcome, as usual.
Vy 73
Bruce PY2BS
qrv 70cm, 33cm, 23cm, 13cm, 9cm, 6cm and 3cm.
I am almost done with firmware for MABMPU simple controller. This is a potential replacement for DRO levels that can be expanded in the future to work with various popular EME trackers like RazTrak, DrzTrack, OE5JFL, F1EHN.
In order to use this setup, one MABMPU encoder board takes on role of the controller and reads the US Digital SEI bus encoders and displays the results on the LCD. This simple controller works with US Digital A2 and A2T encoders or MABMPU encoder board (using MAB25, MAB28, ETS25 or MPU9150 inclinometer).
Power (+12VDC) is provided to the encoders over the 6-wire CAT-3 cable from the MABMPU simple controller. In theory, the US Digital SEI bus can drive cables over 100m.
For those that already have a EME tracker which utilizes US Digital encoders, I have a version of the MABMPU LCD firmware that monitors the SEI encoder bus for encoder read position commands and simply displays the positions on the LCD display. In this configuration, the power to the MABMPU monitor is obtained from the SEI 6-wire bus.
Simple Controller:
https://www.dropbox.com/sh/967cur8w88zrtgh/AAA5N_CrlFZpQsHmjIBwP2vaa?dl=0
More photos:
https://www.dropbox.com/sh/8h6cp0hw463rekc/AACK_Lv0Nswr_P0mWGIDkwoLa?dl=0
Gary, N8CQ
Hi all,
check out http://www.darkside.cz/eme.php
By the way I'll not take a part this time because of
IARU R1 UHF/SHF Contest. I'll be running
this UHF Contest with my club OK2A on 70/23/9/3cm.
73
Matej, OK1TEH
Hello,
I just acquired a 3m dish and would like to know what is
recommended for the best type of feed for 1296 and where could I
purchase one?
73, Al K7CA
My digital tracking system, marketed by Gary Abercrombie - N8CQ, is
now functional.
I finished a write-update at: http://www.kl7uw.com/RazTrak.htm
Also found by a link from my Tech Topics webpage.
I used it on 28 March on 2m-eme.
I will also be used for 6m tracking when the new antenna array goes up in May.
73, Ed - KL7UW
http://www.kl7uw.com
Dubus-NA Business mail:
dubususa(a)gmail.com
Is anyone using a program called TRIMBLE to keep time on your computer??
A few weeks back I installed a GPS receiver to keep one of my laptop off the Internet but still keep accurate time for WSJT.
The problem is it will not switch to daylight saving time. I did it manually but it reverts back to 1 hour ahead. The minutes & seconds are OK it is only the HOUR which is giving me grief. IF you are using this GP software please get in touch with me
Thank you
Serge VE1KG
